View A121EW02V0_7876780.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 1/26 document version: 4.0 date: 2007/01/12 product functional specification 12.1 inch wide xga color tft lcd module model name: a121ew02 v0 ( ) preliminary specification ( ) final specification note: this specification is subject to change without prior notice. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 2/26 contents 1.0 handling precautions.....................................................................................................................5 2.0 general description..........................................................................................................................6 2.1 display characteristics....................................................................................................................6 2.2 functional block diagram................................................................................................................7 3.0 absolute maximum ratings.............................................................................................................8 3.1 absolute maximum ratings of the lamp .7 4.0 optical characteristics ...............................................................................................................................9 4.1 signal description 9 5.0 signal interface...............................................................................................................................10 5.1 connectors......................................................................................................................................11 5.2 signal pin........................................................................................................................................12 5.3 signal description..........................................................................................................................12 5.4 interface timing..............................................................................................................................13 5.5 signal electrical characteristics...................................................................................................14 5.6 signal for lamp connector............................................................................................................16 6.0 pixel format image.........................................................................................................................16 7.0 parameter guide line for ccfl inverter........................................................................................17 8.1 timing control................................................................................................................................18 8.1 timing characteristics...................................................................................................................18 8.2 timing definition.............................................................................................................................18 9.0 power consumption.......................................................................................................................19 10.0 power on/off sequence............................................................................................................20 11.0 reliability /safety requirement....................................................................................................21 12.0 outline drawing .22 13.0 lot definition ..23 14.0 packaging description ........24 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 3/26 ii record of revision version and date page old description new description remark v0. 2006/04/20 first draft v1. 2006/05/19 spec revised after mock-up sample finished v2 2006/6/16 review the spec sheet thoroughly. 7 none absolute maximum ratings of the lamp set 3.1 8 none brightness min. 4.0 8 none the condition of the optical measurement 4.0 13 none note1: define rxinx; note2: define rxclkin 5.4 20 none esd ra condition 11.0 v3 2006/7/7 7 none temperature and relative humidity graph 3.0 7 none note 2 3.0 7 operating temperature max(+70) operating temperature max: 70 3.0 7 storage temperature max(+70) storage temperature max: 70 3.0 8 viewing angle u/d/l/r (50)/(65)/(65)/(65) viewing angle u/d/l/r 50/65/65/65 4.0 8 none luminance uniformity 4.0 9 none signal name consistency: dsptmg de 5.3 20 low temperature storage: ta=0 low temperature storage: ta=-20 11.0 20 low temperature operation: ta=-20 low temperature operation: ta=0 11.0 20 vibration sweep: 2.9g vibration sweep: 3.0g 11.0 21 outline drawing modification 12.0 v3.1 2006/7/12 15 none add lamp(a) and lamp(b) 5.6 v3.2 2006/7/13 7 +70 ta:+70/tp:+71 3.0 20 tp: 70 tp: 71 11.0 7 none ta/tp definition 3.0 20 tp: panel surface temperature. tp: center point temperature of panel surface. 11.0 v3.3 2006/7/21 6 278.2(w) x 183.7(h) x 13.5(d) 278.2(w) x 183.7(h) x 13.8(d) 2.1 v3.4 2006/7/27 6 278.2(w) x 183.7(h) x 13.5(d) 278.2(w) x 184.0(h) x 13.8(d) 2.1 6 710g 750g 2.1 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 4/26 22 none add note 2 12.0 v3.5 2006/8/18 9 color / chromaticity coordinates (cie) rang +- 0.03 4.0 22 lvds 1 st pin marking, redefine inv erter cable length; 12.0 v3.6 2006/8/21 9 bx : 0.09, 0.12, 0.15 bx: 0.12, 0.15, 0.18 4.0 v3.7 2006/9/15 20 t1/min: 0.5ms; max: 10ms t1/min: 0.4ms /max: 50ms 10.0 20 t7/max: 10ms t7/max: 1000ms 10.0 23 none lot definition 13.0 24,25 none packaging description 14.0 v3.8 2006/10/4 20 t7 min: 0ms; max: 1000ms eliminate the definition of t7 10.0 v3.9 2006/11/10 24 packaging description update drawing 14.0 v4.0 2007/1/12 final specifications www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 5/26 1.0 handling precautions 1) do not press or scratch the surface harder than a hb pencil lead because the polarizers are very fragile and could be easily damaged. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water droplets or oil immediately. long contact with the droplets may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) protect the module from static electricity and insure proper grounding when handling. static electricity may cause damage to the cmos gate array ic. 7) do not disassemble the module. 8) do not press the reflector sheet at the back of the module. 9) avoid damaging the tft module. do not press the center of the ccfl reflector when it was taken out from the packing container. instead, press at the edge of the ccfl reflector softly. 10) do not rotate or tilt the signal interface connector of the tft module when you insert or remove other connector into the signal interface connector. 11) do not twist or bend the tft module when installation of the tft module into an enclosure (notebook pc bezel, for example). it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside when designing the enclosure. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local regulations for disposal. 13) the lcd module contains a small amount of material that has no flammability grade, so it should be supplied by power complied with requirements of limited power source (2.11, iec60950 or ul1950). 14) the ccfl in the lcd module is supplied with limited current circuit (2.4, iec60950 or ul1950). do not connect the ccfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 6/26 2.0 general description this specification applies to the 12.1 inch wide color tft/lcd module a121ew02 v0 this module is designed for a display unit of portable video devices. the screen format is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. this module does not contain an inverter card for backlight. 2 2 . . 1 1 d d i i s s p p l l a a y y c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 307.9(12.1" wide) active area [mm] 261.12(h) x163.2 (v) pixels h x v 1280(x3) x 800 pixel pitch [mm] 0.204 x 0.204 pixel arrangement r.g.b. vertical stripe display mode normally white typical white luminance(ccfl=6.0ma) [cd/m 2 ] 450 typ. contrast ratio 350:1 response time [msec] 30 typ. nominal input voltage vdd [volt] +3.3 typ. weight [grams] 750g typ. physical size [mm] 278.2(w) x 184.0(h) x 13.8(d) electrical interface lvds color depth 262k colors temperature range operating storage (shipping) [ o c] [ o c] 0 to +70 -20 to +70 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 7/26 2 2 . . 2 2 f f u u n n c c t t i i o o n n a a l l b b l l o o c c k k d d i i a a g g r r a a m m the following diagram shows the functional block of the 12.1 inches color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1280 x 3 x 800 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) hirose df19la-20p-1h(56) mating type df19g-20s-1c mating type jst sm04(4.0)b-bhs-1-tb lamp connector( 4 pin) x 2 jst bhr-04vs-1 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 8/26 3.0 absolute maximum ratings absolute maximum ratings of the module is as following: item symbol min max unit conditions logic/lcd drive voltage vdd -0.3 +4.0 [volt] input voltage of signal vin -0.3 vdd+0.3 [volt] operating temperature top 0 ta:+70/tp:+71 [ o c] note 2 operating humidity hop 5 90 [%rh] note 1 storage temperature tst -20 +70 [ o c] storage humidity hst 5 90 [%rh] note 1 note 1 : maximum wet-bulb should be 39 and no condensation. note2: ta: ambient temperature; tp: center point temperature of panel surface. twb=39 c operating range storage range note 2 : high operating temperature may cause the slight material variation. we assure under the above condition, the module set keep the function normal display. 3.1 absolute maximum ratings of the lamp set item symbol min max unit conditions lamp set current il - 7.0 marms note 1 lamp set voltage vl - 1600 vrms note 2 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 9/26 note 1 : refer to the lamp spec (a) the above characteristics are measured under the conditions as following: ambient temperature:25 2 ; relative humidity:65 20%rh (b) the inverter condition in vendor site is: vin=12v,c=15pf,frequency:46khz. note 2 : refer to the connector of the lamp set. 4.0 optical characteristics item unit conditions min. typ. max. remark viewing angle [degree] [degree] horizontal (right) cr = 10 (left) 50 50 65 65 - - cr: contrast ratio [degree] [degree] vertical (upper) cr = 10 (lower) 35 50 50 65 - - contrast ratio 300 350 - [msec] rising - 12 50 response time [msec] falling - 18 60 white x 0.28 0.31 0.34 note1 white y 0.30 0.33 0.36 note1 red x 0.61 0.64 0.67 red y 0.31 0.34 0.37 green x 0.25 0.28 0.31 green y 0.56 0.59 0.62 bule x 0.12 0.15 0.18 color / chromaticity coordinates (cie) blue y 0.04 0.07 0.10 white luminance ccfl @ 6.0ma [cd/m2] central 400 450 - note1 luminance uniformity % 70 note2 note 1 : ambient temperature =25 . and lamp current i l = 6 marms. to be measured in the dark room below 10 lux and to be measured on the center area of panel with a viewing cone of 1 by topcon luminance meter bm-7, after 20 minutes operation. note 2 : luminance uniformity of these 9 points is defined as below: 50 % 90 % 90 % 50 % 10 % 10 % www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 10/26 4.1 signal description signal name description rxin0n, rxin0p lvds differential data input (r0~r5, g0) rxin1n, rxin1p lvds differential data input (g1~g5, b0~b1) rxin2n, rxin2p lvds differential data input (b2~b5, hsync, vsync, de) rxclkinn, rxclkinp lvds differential clock input vdd +3.3v power supply gnd ground note1: start from right side note2: please follow vesa. note3: input signals shall be low or hi-z state when vdd is off. internal circuit of lvds inputs are as following. connector 20 1 www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 11/26 the module uses a 100ohm resistor between positive and negative data lines of each receiver input 5.0 signal interface 5 5 . . 1 1 c c o o n n n n e e c c t t o o r r s s physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for signal connector manufacturer hirose t ype / part number df19la-20p-1h(56) mating housing/part number df19g-20s-1c or compatible www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 12/26 connector name / designation for lamp connector manufacturer jst type / part number bhr-04vs-1 mating housing/part number sm04(4.0)b-bhs-1-tb 5 5 . . 2 2 s s i i g g n n a a l l p p i i n n pin# signal name pin# signal name 1 gnd 2 vdd 3 vdd 4 vdd e did 5 aging 6 clk e did 7 data edid 8 rxin0n 9 rxin0p 10 gnd 11 rxin1n 12 rxin1p 13 gnd 14 rxin2n 15 rxin2p 16 gnd 17 rxclkinn 18 rxclkinp 19 gnd 20 gnd note: add 1k ohm resister and connect to grounding as the solution for not adopting pin4, pin5, pin6, and pin7. 5 5 . . 3 3 s s i i g g n n a a l l d d e e s s c c r r i i p p t t i i o o n n the module uses a lvds receiver embedded in auo s asic. lvds is a differential signal technology for lcd interface and high-speed data transfer device. signal name description rxin0-, rxin0+ lvds differential data input(red0-red5, green0) rxin1-, rxin1+ lvds differential data input(green1-green5, blue0-blue1) rxin2-, rxin2+ lvds differential data input(blue2-blue5, hsync, vsync, de) rxclkin-, rxclkin0+ lvds differential clock input vdd +3.3v power supply gnd ground note : input signals shall be in low status when vdd is off. internal circuit of lvds inputs are as following. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 13/26 signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the signal is used to strobe the pixel data. de display timing when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync vertical synchronized signal hs horizontal sync horizontal synchronized signal note: output signals from any system shall be low or hi-z state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 14/26 5 5 . . 4 4 i i n n t t e e r r f f a a c c e e t t i i m m i i n n g g note1. rxinx can be rxin0, rxin1, or rxin2. note2. rxclkin: refer to the signal description in page 11 of this spec sheet. symbol parameter min. typ. max. units ttcp clk in period t ttop1 output data position1 -0.3 0 0.3 ns ttop0 output data position0 t/7-0.3 t/7 t/7+0.3 ns ttop6 output data position6 2/7 t-0.3 2/7 t 2/7 t+0.3 ns ttop5 output data position5 3/7 t-0.3 3/7 t 3/7 t+0.3 ns ttop4 output data position4 4/7 t-0.3 4/7 t 4/7 t+0.3 ns ttop3 output data position3 5/7 t-0.3 5/7 t 5/7 t+0.3 ns ttop2 output data position2 6/7 t-0.3 6/7 t 6/7 t+0.3 ns www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 15/26 5 5 . . 5 5 s s i i g g n n a a l l e e l l e e c c t t r r i i c c a a l l c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s input signals shall be low or hi-z state when vdd is off. it is recommended to refer the specifications. item symbol min. typ. max. unit condition differential input voltage vid 0.1 - 0.6 v lvds input common mode voltage vcm 1 1.2 1.5 v vth/vtl=+-100mv differential input high threshold voltage vth - - 100 mv differential input low thre s ho l d vo l tage vtl -100 - - mv vcm=1.2v note: lvds signal waveform www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 16/26 5 5 . . 6 6 s s i i g g n n a a l l f f o o r r l l a a m m p p c c o o n n n n e e c c t t o o r r pin # signal name 1 lamp(a) high voltage 2 lamp(a) low voltage 3 lamp(b) low voltage 4 lamp(b) high voltage 6.0 pixel format image following figure shows the relationship of the input signals and lcd pixel format. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 17/26 7.0 parameter guide line for ccfl inverter parameter min typ max units condition ccfl current(icfl) 4.0 6.0 7.0 [ma] rms (ta=25 ) note 2 ccfl frequency(fcfl) 45 52 70 [khz] (ta=25 ) note 3 ccfl starting voltage (vscfl) 1,200 ? ? [volt] rms (ta= 0 ) note 4 ; note 6 ccfl starting voltage (vscfl) 900 ? ? [volt] rms (ta= 25 ) note 4 ; note 6 ccfl voltage (reference) (vcfl) ? 538 ? [volt] rms (ta=25 icfl=6ma) note 5 single ccfl power consumption (pcfl) ? 3.3 ? [watt] (ta=25 icfl=6ma) note 5 note 1 : typ is auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time after applying start-up voltage. it is recommended to keep on applying start-up voltage for 1 [sec] until discharge. *5 the ccfl inverter operating frequency must be carefully chosen so that no interfering noise stripes on the screen were induced. *6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2 : it should be employed the inverter, which has duty dimming , if iccfl is less than 4ma. note 3 : the ccfl inverter operating frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the inverter open voltage should be designed larger than the lamp starting voltage at t=0 o c, otherwise backlight may be blinking for a moment after turning on or not be able to turn on. the open voltage should be measured after ballast capacitor. if an inverter has shutdown function it should keep its open voltage. for longer than 1 second even if lamp connector is open. note 5 : calculator value for reference (icfl vcfl=pcfl) note 6 : ccfl starting voltage is defined the minimum starting voltage for inverter design reference. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 18/26 8.0 timing control 8 8 . . 1 1 t t i i m m i i n n g g c c h h a a r r a a c c t t e e r r i i s s t t i i c c s s this is the signal timing required at the input of the user connector. all of the interface signal timing should be satisfied with the following specifications. parameter symbol min. t yp. max. unit frame rate - 50 60 - hz c l ock f requency 1/ t c lo ck 62 68.9 75 mhz per i od t v 803 816 832 act i v e t v d 800 800 800 vertical section b l ank i ng t v b 3 16 32 t line period t h 1302 1408 1700 active t h d - 1280 - horizontal section b l ank i ng t h b 22 128 420 t clock note : de mode only 8 8 . . 2 2 t t i i m m i i n n g g d d e e f f i i n n i i t t i i o o n n www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 19/26 9.0 power consumption input power specifications are as follows; symbol parameter min typ max units condition module vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] load capacitance 20uf pdd vdd power 1.6 [watt] all black pattern pdd max vdd power max 1.7 [watt] max pattern (note 1) idd idd current 400 ma 64 grayscale pattern idd max idd current max 650 ma vertical stripe line pattern (note 1) vddrp allowable logic/lcd drive ripple voltage 500 [mv] p-p vddns allowable logic/lcd drive ripple noise 100 [mv] p-p note 1: vdd=3.3v note 2: a121ew02 v0 module includes four lamps. note 3: ccfl starting voltage is defined the minimum starting voltage for inverter design reference. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 20/26 10. power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. t1 90% 90% 10% 10% power supply vdd t2 t3 t4 lvds interface valid t5 data t6 backlight on power sequence timing value parameter min. t yp. max. units t1 0.4 - 50 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 500 - - (ms) t5 200 - - (ms) t6 200 - - ( m s) note 1: t5, t6 is only for assuring the display quality. (t5,t6 spec may be ignored if don t care the display quality.) www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 21/26 11.0 reliability /safety requirement r r e e l l i i a a b b i i l l i i t t y y t t e e s s t t c c o o n n d d i i t t i i o o n n s s no. test items conditions remark 1 high temperature storage ta= 70 240hrs 2 low temperature storage ta= -20 240hrs 3 high temperature operation tp= 71 240hrs 4 low temperature operation ta= 0 240hrs 5 high temperature and high humidity tp= 50 , 80% rh 240hrs operation 6 thermal shock -20 c to +60 c, ramp 20 c/min, duration at temp. = 30min, test cycles = 50 non-operation frequency range : 8~33.3hz stoke : 1.3mm sweep : 3.0g, 33.3 ~ 400hz cycle : 15 minutes 2 hours for each direction of x,z 7 vibration 4 hours for y direction jis d1601, a-10 condition a 8 mechanical shock 100g, 6ms, x, y, z 3 times for each direction jis c0041, a-7 condition c 9 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz C 6db/octave from 200~500hz iec 68-34 10 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces jis z0202 contact discharge: 8kv, 150pf(330 ) 1sec, 8 points, 25 times/ point. 11 electro static discharge (esd) air discharge: 15kv, 150pf(330 ) 1sec, 8 points, 25 times/ point. operation & non-operation note1: ta: ambient temperature. note2: tp: center point temperature of panel surface. note3: all the cosmetic specification is judged before the reliability stress. ccfl life time: 10,000 hours minimum the ccfl life time is defined as the module brightness decrease to 50% original brightness at ta=25 , i l =6ma. www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 22/26 12. outline drawing www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 23/26 1 1 3 3 . . lot definition a. lot definition of product (product label) a-1. example lot number a-2. manufactured end of year and week mark a. manufactured end of year mark b. manufactured week mark mark 06 07 08 09 definition 2006 2007 2008 2009 mark 01 02 definition 1st week 2nd week b. lot definition of part(blu label) b-1. example lot number b-2. manufactured date www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 24/26 1 1 4 4 . . packaging description a. internal packaging automatic automatic www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 25/26 b. external packaging www.datasheet.co.kr datasheet pdf - http://www..net/
(c) copyright au optronics may, 2005 all rights reserved. a121ew02 v0 no reproduction and redistribution allowed. 26/26 pallet stretch film corner angle pet band www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of A121EW02V0

	To Download A121EW02V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .